Roofing Learning Center | Starway Roof Systems

Why We Use 5/16-Inch ZXL Screws on Metal Roofs, Not 1/4-Inch

Written by Elmer Glick | Nov 22, 2026, 4:48:02 AM

On an exposed fastener metal roof, the screws are the part that wears out first, and it is the rubber washer under each screw head that fails. We install 5/16-inch ZXL screws instead of the usual 1/4-inch screws because the ZXL has a cap that covers the washer and shields it from the sun. Standard screws typically need replacing every 12 to 15 years. ZXL screws should last longer, though they may still need replacing around 20 years.

Below we explain how exposed fastener roofs are held down, why the washers fail, what makes a ZXL screw different, and what it means for the long-term cost of your roof.

Watch: why Starway Roof Systems uses 5/16-inch ZXL screws instead of 1/4-inch screws.

Key Takeaways: ZXL Screws on Metal Roofs

  • Exposed fastener metal panels are screwed down through the face of the metal, and every screw seals with a rubber washer.
  • Sunlight breaks down those rubber washers over time. Once they dry out and crack, water can get in at the screw.
  • On a standard 1/4-inch screw, the washer is a separate piece whose edge sits out in the sun.
  • On a 5/16-inch ZXL screw, a zinc-aluminum cap covers the washer and protects it from UV.
  • Standard screws typically need replacing every 12 to 15 years. ZXL screws should last longer, but may still need replacing around 20 years.
  • Standing seam metal hides its fasteners, so it has no exposed screws to replace.

How Exposed Fastener Metal Roofs Are Held Down

Exposed fastener panels, sometimes called screw-down panels, are fastened with screws driven straight through the face of the metal into the wood or steel underneath. Depending on the size of the roof, that can be hundreds or thousands of screws.

Each screw has a rubber washer under its head. When the screw is driven, the washer squeezes against the panel and seals the hole. That washer is what keeps water out at every one of those screws.

Exposed fastener panels cost less than standing seam and go on faster, which is why they are popular on homes, barns and garages around Central PA. The tradeoff is those washers.

Why Metal Roof Screws Wear Out

The Sun Breaks Down the Rubber Washer

Rubber that sits in direct sun for years dries out, hardens and cracks. Once the washer can no longer press tight against the panel, water can follow the screw into the roof.

Panels Move With Every Temperature Swing

Metal expands as it heats up and shrinks as it cools, and Central PA can swing a long way between a cold night and a sunny afternoon. Each swing works the panels against the screws, which can slowly loosen them and wear the washers.

Signs Your Screws Need Attention

  • Washers that look cracked, flattened or brittle
  • Screws that have backed out and sit above the panel
  • Rust stains running down from screw heads
  • Drips inside that line up with a row of screws during or after rain

Worn screws do not always mean you need a new roof. On many roofs, the screws can be replaced. Replacing them typically costs $3,500 to $12,000, depending on the size and steepness of the roof.

If water drips inside on dry, cool mornings instead, it is more likely condensation than a leak. Our post on metal roof condensation and DripStop explains the difference.

What Makes a ZXL Screw Different

Standard 1/4-Inch Screw: The Washer Sits Out in the Sun

On the standard screw most exposed fastener roofs use, the rubber washer is a separate piece under a 1/4-inch hex head. Its edge sits out from under the head, right where the sun hits it every day.

5/16-Inch ZXL Screw: A Cap Covers the Washer

The ZXL screw has a larger 5/16-inch head with a cap made of a zinc-aluminum alloy that covers the washer. The sun cannot reach the rubber, so it does not dry out and crack as quickly. The manufacturer also says the cap protects the head from red rust.

Standard 1/4-inch screw 5/16-inch ZXL screw
Head size 1/4-inch hex head 5/16-inch hex head
Rubber washer Separate piece under the head, with its edge exposed Covered by a zinc-aluminum cap
Sun on the washer Every day Shielded from UV
Typical replacement Every 12 to 15 years Longer, but may need replacing around 20 years

How Long ZXL Screws Last

Standard screws typically need replacing every 12 to 15 years. ZXL screws should last longer than that, but they may still need replacing around 20 years. No screw on an exposed fastener roof lasts as long as the panels.

Over the life of the roof, that can mean one less round of screw replacement, and fewer years with worn washers on your roof.

Exposed Fastener vs. Standing Seam

If you would rather never replace screws, standing seam metal hides its fasteners under the seams, so there are no washers out in the weather. It costs more up front. On a home under 2,500 square feet in Central PA, exposed fastener metal runs about $10,500 to $41,500 and standing seam about $21,000 to $65,000. Our roof replacement cost guide breaks those ranges down by home size and roof pitch.

Exposed fastener metal with ZXL screws is a good middle ground if you want a metal roof at a lower price and are fine planning for screw replacement down the road. It is also a common choice for barns, garages and other outbuildings. On those, ask about DripStop as well, since uninsulated buildings are where condensation causes the most trouble.

What Central PA Homeowners Should Do Next

If you are getting quotes for an exposed fastener metal roof, ask which screws are included. Ours use 5/16-inch ZXL screws. If you already have an exposed fastener roof that is 12 or more years old, have the screws checked before a small leak at a screw turns into rotted decking.

  • For a ballpark price on a new roof in a few minutes: use our instant quote tool.
  • For an exact price, or a look at your screws: schedule a free roof inspection or call us at (814) 308-0490.

To compare exposed fastener and standing seam roofs side by side, see our metal roofs page.

FAQs About Metal Roof Screws

How often do metal roof screws need to be replaced?

Standard screws on an exposed fastener metal roof typically need replacing every 12 to 15 years, because the rubber washers break down in the sun. ZXL screws should last longer, but they may still need replacing around 20 years.

What is a ZXL screw?

A ZXL screw is a metal roofing screw with a 5/16-inch head and a zinc-aluminum cap that covers the rubber washer. The cap shields the washer from the sun's UV, so it lasts longer than the washer on a standard screw.

Why are ZXL screws better than standard 1/4-inch screws?

On a standard 1/4-inch screw, the rubber washer is a separate piece whose edge sits out in the sun. On a ZXL screw, the cap covers the washer and protects it from UV, which is the main thing that wears washers out.

Does Starway use ZXL screws on its metal roofs?

Yes. We use 5/16-inch ZXL screws on the exposed fastener metal roofs we install. Standing seam roofs use hidden fasteners, so they have no exposed screws.

How much does it cost to replace the screws on a metal roof?

Replacing the screws on an exposed fastener metal roof typically costs $3,500 to $12,000 in Central PA, depending on the size and steepness of the roof.

Do standing seam metal roofs need screw replacement?

No. Standing seam roofs hide their fasteners under the seams, so there are no exposed washers to wear out and no screws to replace.

Have a question we didn’t cover? Call Starway Roof Systems: (814) 308-0490